产品中心
产品中心
美孚宝素67
来源于:张家港保税区澳博国际贸易有限公司

简 介
本产品是作为热轧铝材,铝合金和冷轧及热轧有色金属的冷却和润滑剂。采用矿物油,乳化剂,润滑剂,分散剂机润滑性添加剂配制而成。本油配方特别,故无需预热便可在室温下于低于250mg/LCaCO3硬度的自来水搅拌乳化。本产品能于轧制时提供良好的润滑并使轧制品表面良好。
优 点
· 轧制品表面质量稳定和良好,减少啄印
· 在高轧制速度下,仍能有效大的压缩率
· 乳化溶液容易调制
· 乳化液使用寿命长久,增加经济效益
· 乳化液在高温下保持稳定
· 乳化液稳定性可调较
用 途
适用于铝及有色金属的热轧程序,无论在二重和四重初轧及精轧机、线材和带材串联及连续铸造生产线皆可使用。亦可用于有色金属带 材,管材的冷轧程序.宝素 67 是采用非离子乳化剂,故可在室温下以自来水(硬度低于 250mg/LCaCo3) 来调制乳化液,但为了较长的使用寿命,每天补充水份时,建议采用软水为佳.于调制乳化液时,一定是以油加入水中,切不能将程序倒置。
Product Descr1ption
Lubricant and coolant for hot rolling of aluminum and aluminum alloys and for hot and cold rolling of nonferrous metals. The product is made from mineral oil, emulsifying,wetting and loosening agents and emulsifying with tap water with hardness below 250mg/L CaCo3 and stirring at room temperature without preheating. The product provides good lubricity and good surface quality of the rolled strip.
Benefits
· Good constant surface quality, less pock up
· High reductions at high rolling speed
· Easy preparation of emulsion
· Economical due long life of emulsion
· High temperature stability, high hot strip temperature obtained
· Adjustable emulsion stability
Application
For hot rolling of aluminum and nonferrous metals in 2-Hi and 4-Hi breakdown and finishing mills, in tandem mills and in continuous casting lines for wires and strips. Also suitable for cold rolling of nonferrous metals in strip and tube mills. Prosol 67 is based on a non ionic emulsifier system, therefore the use of tap water ( hardness below 250mg / L CaCo3 ) at room temperature is possible for preparing the emulsion. For daily topping up the use of demineralized water is recommended to achieve long emulsion life. The oil must always be added to water and not vice versa.

Characteristics 特 性以 下 所 列 数 据 除 特 别 注 明 外, 均 为 典 型 值
Typical values unless otherwise stated

Color
色度

2.0

Density @ 15°C,kg/L
密度@15°C,千克/升

0.92

Pour Point,℃
顷点 ℃

-27

Neutralization Number, mg KOH/g
中和值,毫克 KOH /

2.1

Saponification Number, mg KOH/g
皂碱值,毫克 KOH / 克

26.5

TBN, mg KOH/g
总碱值,毫克 KOH / 克

6.0

Emulsion (6% in deionized Water)

与去离子水制成浓度 6 % 的乳化液

Appearance
外观

Milky White
奶白色

pH Value at 200C
200C 时 pH

8.7

Stability, 24 hours @ room temperature
乳化液稳定性测试, 24 小时,室温

1.0 % Cream
1.0 % 奶油层