产品中心
产品中心
美孚润滑脂CM-P和CM-L
来源于:张家港保税区澳博国际贸易有限公司

简 介
美孚润滑脂CM-P和CM-L是极压润滑脂。美孚润滑脂CM-P为2号脂,而CM-L为1号脂。这两种产品均为高温复合锂基脂,在严苛的工况下,展示出卓越的抗软化性能,并具有良好的防水性。所含的极压添加剂能提供优异的抗磨和抗冲击负荷保护,而其他的添加剂提供抗高温氧化和防锈保护。美孚润滑脂CM-P和CM-L亦具有低温分散性,抗水洗性用于高温轴承仍有较长的使用寿命。美孚润滑脂CM-P和CM-L具有杰出的组织结构和化学稳定性,适用于重负荷及严苛工况的应用。它们不会腐蚀钢或铜合金轴承并且与传统的密封材料相容。
用 途
美孚CM-P推荐用于高负载滑动和抗磨轴承以及需要含3%二硫化钼及高温稠化剂来提供特殊性能的应用。美孚CM-L为冬天级产品,因此一般推荐用于较冷的地区。

Product Descr1ption
Mobilgrease CM-P, Moiblgrease CM-L are extremepressure greases. Mobilgrease CM-P NLGI Grade 2, while CM-L is NLGI Grade 1. All two products have a high-temperature lithium complex thickener system , exhibit excellent resistance to softening under severe working, and provide good water resistance. An extreme-pressure additive provides exceptional protection against wear and shock loads, while additional additives enhance resistance to hightemperature oxidation and protection against rust. Other formulation features provide low temperature dispensing, good resistance to water wash, and long service in bearings operating at high temperatures. These heavy-duty, severe-service greases have outstanding structural and chemical stability. They won't corrode steel or copper-bearing alloys and are compatible with conventional seal materials.
Application
Mobilgrease CM-P is recommended for highly loaded plain and antifriction bearings and other applications where the three percent molybdenum disulfide and high-temperature thickener system will provide extraordinary performance. Mobilgrease CM-L is a winter-grade products and, therefore, is recommended for cold-temperature service.

Characteristics 特 性以 下 所 列 数 据 除 特 别 注 明 外, 均 为 典 型 值
Typical values unless otherwise stated

Mobilgrease CM-P,CM-L
美 孚 润 滑 脂 CM-P, CM-L


CM-PCM-L

NLGI Grade
NLGI 编号

21

Soap Type
皂基

Lithium Complex with EP
Additives ( 3% moly )
复合锂及EP添加剂
(含3%二硫化钼)
Lithium Complex with EP
Additives ( 3% moly )
复合锂及EP添加剂
(含3%二硫化钼)

Structure
结构

Smooth/Tacky
光滑/粘
Smooth/Tacky
光滑/粘
Color, Visual
颜色
Gray/Black
灰色/黑色
Gray/Black
灰色/黑色
Oil Viscometrics, ASTM D 445
基础油粘度,ASTM D 445
cSt @ 40 °C 厘斯
cSt @ 100 °C 厘斯
SUS @ 100 °F 赛氏
SUS @ 210 °F 赛氏
320
27
1690
133
150
16
783
84
Dropping Pt , °C ( °F ), ASTM D 2265
滴点 °C ( °F ), ASTM D 2265
260 (500)260 (500)
Corrosion Prevention , ASTM D 1743
防锈保护, ASTM D 1743
Pass
通过
Pass
通过
Timken OK Load, ASTM D 2782 , lb, min.
Timken 试验负荷,ASTM D 2782, 镑,不小于
4545
Four-Ball EP Weld Load, ASTM D 2596 , kg, min.
四球烧结负荷,ASTM D 2596, 公斤,不小于
250250
Four-Ball Wear Test , scar , ASTM D 2266, mm
四球磨损试验,刮痕,ASTM D 2266, 毫米
0.50.5