产品中心
产品中心
美孚力富 SHC PM
来源于:张家港保税区澳博国际贸易有限公司

简 介
美孚力富SHCPM造纸机用合成滑脂是一种奶白色,结合了具独特性能的合成基础油及复合锂基增稠剂的特别高性能滑脂。它的NLGI等级是1.5而基础油的ISO粘度等级是460。
用途
美孚力富SHCPM被推荐用于造纸机中重要的滚动轴承。它提供杰出的保护对抗生锈及酸化水,令它成为造纸机湿部的最理想滑脂。由于使用高粘度的基础油,此滑脂在高负荷,低至中速的压榨部轴承中使用时表现杰出。合成基础油的低挥发性及杰出的高温氧化稳定性使滑脂的添补周期延长并使在高温操作的毯辊轴承及超级压光机轴承的寿命大大延长。
优点
·广阔的操作温度由-40°C 至180°C
·杰出的防腐蚀保护对抗酸化水
·即使在有水的工况亦能保持突出的结构稳定性
·在高负荷,低速及高温下仍提供杰出的抗磨保护
·挥发性低
·延长滑脂的添补周期
·节约能源
·不含铅、氯及亚硝酸盐

Product Descr1ption
Mobilith SHC PM (Paper Machine) is a cream-colored, very high performance grease which combines the unique features of a synthetic base fluid with a lithium complex soap thickener. It has an NIGI grade of 1.5 and a base fluid ISO VG of 460.
Application
Mobilith SHC PM is recommended for critical rolling element bearing applications in paper machines. It provides outstanding protection against rust and acid water corrosion, making it ideal for the wet end of the paper machine. Through the use of high viscosity base fluid, the grease is excellent for highly loaded, low to moderate speed press section bearings. The low volatility and excellent high-temperature oxidation stability of the synthetic base fluid maximize relubrication intervals and bearing life in the high –temperature felt roll and calender stack bearings.
Properties
·Operating range of -40 ℃ to +180 ℃
·Wide operating temperature range of -40°C to 180°C.
·Excellent corrosion protection from acid water
·Outstanding structural stability in the presence of water
·Excellent wear protection under heavy loads, slow speeds and high temperatures
·Low volatility
·Extended relubrication intervals
·Reduced energy consumption
·Lead, chlorine and nitrite free

Characteristics 特 性以 下 所 列 数 据 除 特 别 注 明 外, 均 为 典 型 值
Typical values unless otherwise stated

Mobilith SHC Synthetic Grease
美 孚 力 富 SHC 合 成 润 滑 脂

NLGI Grade
NLGI 级 别

ASTM D2171.5

Soap Type 皂 基

Red 红Red 红Red 红

Penetration, Worked 60 strokes,
针 入 度, 工 作 60 次 后

Lithium Complex
复 合 锂
Structure
结 构
Visual
目 测
Smooth; Slightly Tacky
光 滑, 微 粘
Color
颜 色
Visual
目 测
Cream
奶 白 色
Penetration , Worked
针 入 度 , 操 作 后
ASTM D217305

Dropping Point, °C
滴 点,°C

ASTM D2265250

Viscosity of Oil 基 础 油 粘 度
cSt @ 40 ℃ 厘 斯
cSt @ 100 ℃ 厘 斯

ASTM D445460
46.5

4-Ball Wear, Scar mm
4 球 磨 损 试 验, 疤 痕 毫 米

ASTM D22660.5

4-Ball Weld Test, Kg(N)
4 球 烧 结 负 荷,公 斤

Pass
ASTM D2596
250

Timken OK Load , Kg
梯 姆 肯 OK 值 , 公 斤

ASTM D250922.7

Emcor Rust Test with
4.5 pH Acid Water
4.5 pH 酸 化 水 的 Emcor 测 试

IP 220 Mod.
改 良 的 IP220
0-0

Water Spray , % Loss
被 水 喷 射 后 的 损 失,%

ASTM D404960